View NCP51106_1287825.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

NCP511 150 mA CMOS Low Iq Low-Dropout Voltage Regulator
The NCP511 series of fixed output low dropout linear regulators are designed for handheld communication equipment and portable battery powered applications which require low quiescent current. The NCP511 series features an ultra-low quiescent current of 40 mA. Each device contains a voltage reference unit, an error amplifier, a PMOS power transistor, resistors for setting output voltage, current limit, and temperature limit protection circuits. The NCP511 has been designed to be used with low cost ceramic capacitors and requires a minimum output capacitor of 1.0 mF. The device is housed in the micro-miniature TSOP-5 surface mount package. Standard voltage versions are 1.5 V, 1.8 V, 2.5 V, 2.7 V, 2.8 V, 3.0 V, 3.3 V, and 5.0 V. Other voltages are available in 100 mV steps.
Features http://onsemi.com
5 1 TSOP-5 (SOT23-5, SC59-5) SN SUFFIX CASE 483
* * * * * * * * * * * *
Low Quiescent Current of 40 mA Typical Low Dropout Voltage of 100 mV at 100 mA Excellent Line and Load Regulation Maximum Operating Voltage of 6.0 V Low Output Voltage Option High Accuracy Output Voltage of 2.0% Industrial Temperature Range of -40C to 85C Pb-Free Packages are Available Cellular Phones Battery Powered Instruments Hand-Held Instruments Camcorders and Cameras
PIN CONNECTIONS AND MARKING DIAGRAM
Vin GND Enable 1 xxxAYWG G (Top View) xxx = Specific Device Code A = Assembly Location Y = Year W = Work Week G = Pb-Free Package (Note: Microdot may be in either location) 2 3 5 Vout
4 N/C
Typical Applications
ORDERING INFORMATION
See detailed ordering and shipping information in the package dimensions section on page 10 of this data sheet.
Vin 1 Thermal Shutdown Driver w/ Current Limit 5
Vout
Enable ON OFF 3
GND
2
This device contains 82 active transistors
Figure 1. Representative Block Diagram
(c) Semiconductor Components Industries, LLC, 2006
1
February, 2006 - Rev. 10
Publication Order Number: NCP511/D
NCP511
A AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAA AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA A AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA
PIN FUNCTION DESCRIPTION
Pin No. 1 2 3 4 5 Pin Name Vin Description Positive power supply input voltage. Power supply ground. GND Enable N/C This input is used to place the device into low-power standby. When this input is pulled low, the device is disabled. If this function is not used, Enable should be connected to Vin. No internal connection. Vout Regulated output voltage.
MAXIMUM RATINGS
Rating Input Voltage
Symbol Vin
Value 0 to 6.0
Unit V V V
AAAA AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A AA AAAA A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA A A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AA AAAAAAAAAAA A AA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAA A
Enable Voltage Output Voltage Enable Vout -0.3 to Vin +0.3 -0.3 to Vin +0.3 Power Dissipation and Thermal Characteristics Power Dissipation Thermal Resistance, Junction to Ambient Operating Junction Temperature Operating Ambient Temperature Storage Temperature PD RqJA TJ Internally Limited 250 +125 W C/W C C C TA -40 to +85 Tstg -55 to +150 Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. 1. This device series contains ESD protection and exceeds the following tests: Human Body Model 2000 V per MIL-STD-883, Method 3015 Machine Model Method 200 V 2. Latch up capability (85C) "100 mA DC with trigger voltage.
http://onsemi.com
2
NCP511
ELECTRICAL CHARACTERISTICS (Vin = Vout(nom.) + 1.0 V, Venable = Vin, Cin = 1.0 mF, Cout = 1.0 mF, TJ = 25C, unless
otherwise noted.) Characteristic Output Voltage (TA = 25C, Iout = 1.0 mA) 1.5 V 1.8 V 2.5 V 2.7 V 2.8 V 3.0 V 3.3 V 5.0 V Output Voltage (TA = -40C to 85C, Iout = 1.0 mA) 1.5 V 1.8 V 2.5 V 2.7 V 2.8 V 3.0 V 3.3 V 5.0 V Line Regulation (Iout = 10 mA) 1.5 V-4.4 V (Vin = Vout(nom.) + 1.0 V to 6.0 V) 4.5 V-5.0 V (Vin = 5.5 V to 6.0 V) Load Regulation (Iout = 1.0 mA to 150 mA) Output Current (Vout = (Vout at Iout = 150 mA) -3%) 1.5 V-1.8 V (Vin = 4.0 V) 1.9 V-3.0 V (Vin = 5.0 V) 3.1 V-5.0 V (Vin = 6.0 V) Dropout Voltage (Iout = 100 mA, Measured at Vout -3.0%) 1.5 V 1.8 V 2.5 V 2.7 V 2.8 V 3.0 V 3.3 V 5.0 V Quiescent Current (Enable Input = 0 V) (Enable Input = Vin, Iout = 1.0 mA to Io(nom.)) Output Voltage Temperature Coefficient Enable Input Threshold Voltage (Voltage Increasing, Output Turns On, Logic High) (Voltage Decreasing, Output Turns Off, Logic Low) Output Short Circuit Current (Vout = 0 V) 1.5 V-1.8 V (Vin = 4.0 V) 1.9 V-3.0 V (Vin = 5.0 V) 3.1 V-5.0 V (Vin = 6.0 V) Ripple Rejection (f = 1.0 kHz, Io = 60 mA) Output Noise Voltage (f = 20 Hz to 100 kHz, Iout = 60 mA) 3. Maximum package power dissipation limits must be observed. T *TA PD + J(max) RqJA 4. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible. Symbol Vout 1.455 1.746 2.425 2.646 2.744 2.94 3.234 4.900 Vout 1.455 1.746 2.425 2.619 2.716 2.910 3.201 4.900 Regline - - Regload Iout(nom.) 150 150 150 Vin-Vout - - - - - - - - IQ - - TC Vth(en) 1.3 - Iout(max) 200 200 200 RR Vn - - 400 400 400 50 110 800 800 800 - - dB mVrms - - - 0.3 mA - 0.1 40 "100 1.0 100 - ppm/C V 245 160 110 100 100 100 90 75 350 200 200 200 200 200 200 200 mA - - - - - - mV - 1.0 1.0 0.3 3.5 3.5 0.8 mV/mA mA 1.5 1.8 2.5 2.7 2.8 3.0 3.3 5.0 1.545 1.854 2.575 2.781 2.884 3.09 3.399 5.100 mV/V 1.5 1.8 2.5 2.7 2.8 3.0 3.3 5.0 1.545 1.854 2.575 2.754 2.856 3.06 3.366 5.100 V Min Typ Max Unit V
http://onsemi.com
3
NCP511
200 180 DROPOUT VOLTAGE (mV) 160 140 120 100 80 60 40 20 0 -60 -40 -20 0 Iout = 10 mA 20 40 60 80 Iout = 50 mA Iout = 1 mA Iout = 100 mA Vout(nom.) = 3.0 V Iout = 150 mA Vout, OUTPUT VOLTAGE (V) 3.0 2.5 2.0 1.5 1.0 0.5 0 100 120 140 TEMPERATURE (C) Vout(nom.) = 3.0 V IO = 0 mA Cin = 1.0 mF Cout = 1.0 mF TA = 25C Venable = Vin 0 1 2 3 4 5 6 7 3.5
Vin, INPUT VOLTAGE (V)
Figure 2. Dropout Voltage vs. Temperature
Figure 3. Output Voltage vs. Input Voltage
50 IQ, QUIESCENT CURRENT (mA) 45 40 35 30 25 20 -50 Vin = Vout(nom.) + 0.5 V Vout(nom.) = 3.0 V IO = 0 mA -25 0 25 50 75 100 125 GROUND PIN CURRENT (mA)
45 43 41 39 37 35 33 31 29 27 25 0 25 50 75 100 125 150 TEMPERATURE (C) Iout, OUTPUT CURRENT (mA) Vout(nom.) = 3.0 V Vin = 5.0 V TA = 25C
Figure 4. Quiescent Current vs. Temperature
Figure 5. Ground Pin Current vs. Output Current
45 GROUND PIN CURRENT (mA) 40 CURRENT LIMIT (mA) 35 30 25 20 15 10 5 0 0 1 2 3 4 5 6 Vin, INPUT VOLTAGE (V) Vout(nom.) = 3.0 V Iout = 50 mA TA = 25C
450 400 350 300 250 200 150 100 50 0 0 1 2 3 4 5 6 Vin, INPUT VOLTAGE (V) Vout(nom.) = 3.0 V Cin = 1.0 mF
Figure 6. Ground Pin Current vs. Input Voltage
Figure 7. Current Limit vs. Input Voltage
http://onsemi.com
4
NCP511
Vin, INPUT VOLTAGE (V) Vin, INPUT VOLTAGE (V) OUTPUT VOLTAGE DEVIATION (mV) Vin = 3.5 V to 4.5 V Vout = 3.0 V Cout = 1 mF Iout = 1 mA 5 4 3 60 OUTPUT VOLTAGE DEVIATION (mV) 40 20 0 -20 -40 100 200 300 400 500 600 700 800 900 TIME (ms) 5 4 3 100 50 0 -50 -100 Vin = 3.5 V to 4.5 V Vout = 3.0 V 20 40 60 80 Cout = 1 mF Iout = 100 mA 100 120 140 160 180
TIME (ms)
Figure 8. Line Transient Response
Figure 9. Line Transient Response
Vin, INPUT VOLTAGE (V)
5 4 3 150 100 50 0 -50 -100 -150 -200 20 40 60 80 100 120 140 160 180 TIME (ms) Vin = 3.5 V to 4.5 V Vout = 3.0 V Cout = 1 mF Iout = 150 mA
OUTPUT VOLTAGE DEVIATION (mV)
Figure 10. Line Transient Response
Iout, OUTPUT CURRENT (mA)
150 Vin = 3.5 V Vout = 3.0 V Cin = 1 mF Cout = 10 mF Iout = 1 mA to 150 mA 0
Iout, OUTPUT CURRENT (mA)
150 Vin = 3.5 V Vout = 3.0 V 0
OUTPUT VOLTAGE DEVIATION (mV)
OUTPUT VOLTAGE DEVIATION (mV)
200 100 0 -100 -200
20 10 0 -10 200 400 600 800 1000 1200 1400 1600 1800 TIME (ms)
Cin = 1 mF Cout = 1 mF IO = 1 mA to 150 mA
200 400 600 800 1000 1200 1400 1600 1800 TIME (ms)
Figure 11. Load Transient Response
Figure 12. Load Transient Response
http://onsemi.com
5
NCP511
ENABLE VOLTAGE (V) Vout, OUTPUT VOLTAGE (V) Vin = 3.5 V Vout = 3.0 V TA = 25C Iout = 1 mA Cin = 1 mF
2 1 0 4 3 2 1 0
Cout = 1 mF
Cout = 10 mF
20
40
60
80
100 120 140 160 180
TIME (ms)
Figure 13. Turn-On Response
1.6 OUTPUT NOISE DENSITY (mV/ HZ) RR, RIPPLE REJECTION (dB) 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 0.01 0.1 1.0 10 100 1000 Vout = 1.5 V Vin = 2.5 V Iout = 60 mA Cout = 2.2 mF
70 60 50 40 30 20 10 0 100 1k 10 k f, FREQUENCY (Hz) 100 k 1M Vout = 3.0 V Vin = 3.5 VDC 0.25 V Iout = 60 mA Cout = 1.0 mF
f, FREQUENCY (kHz)
Figure 14. Output Noise Density
Figure 15. Ripple Rejection vs. Frequency
http://onsemi.com
6
NCP511
DEFINITIONS
Load Regulation Line Regulation
The change in output voltage for a change in output current at a constant temperature.
Dropout Voltage
The input/output differential at which the regulator output no longer maintains regulation against further reductions in input voltage. Measured when the output drops 3.0% below its nominal. The junction temperature, load current, and minimum input supply requirements affect the dropout level.
Maximum Power Dissipation
The change in output voltage for a change in input voltage. The measurement is made under conditions of low dissipation or by using pulse technique such that the average chip temperature is not significantly affected.
Line Transient Response
Typical over and undershoot response when input voltage is excited with a given slope.
Thermal Protection
The maximum total dissipation for which the regulator will operate within its specifications.
Quiescent Current
The quiescent current is the current which flows through the ground when the LDO operates without a load on its output: internal IC operation, bias, etc. When the LDO becomes loaded, this term is called the Ground current. It is actually the difference between the input current (measured through the LDO input pin) and the output current.
Internal thermal shutdown circuitry is provided to protect the integrated circuit in the event that the maximum junction temperature is exceeded. When activated at typically 160C, the regulator turns off. This feature is provided to prevent failures from accidental overheating.
Maximum Package Power Dissipation
The maximum power package dissipation is the power dissipation level at which the junction temperature reaches its maximum operating value, i.e. 125C. Depending on the ambient power dissipation and thus the maximum available output current.
http://onsemi.com
7
NCP511
APPLICATIONS INFORMATION A typical application circuit for the NCP511 series is shown in Figure 16.
Input Decoupling (C1) Thermal
A 1.0 mF capacitor either ceramic or tantalum is recommended and should be connected close to the NCP511 package. Higher values and lower ESR will improve the overall line transient response.
Output Decoupling (C2)
The NCP511 is a stable Regulator and does not require any specific Equivalent Series Resistance (ESR) or a minimum output current. Capacitors exhibiting ESRs ranging from a few mW up to 3.0 W can thus safely be used. The minimum decoupling value is 1.0 mF and can be augmented to fulfill stringent load transient requirements. The regulator accepts ceramic chip capacitors as well as tantalum devices. Larger values improve noise rejection and load regulation transient response.
Enable Operation
As power across the NCP511 increases, it might become necessary to provide some thermal relief. The maximum power dissipation supported by the device is dependent upon board design and layout. Mounting pad configuration on the PCB, the board material and also the ambient temperature effect the rate of temperature rise for the part. This is stating that when the NCP511 has good thermal conductivity through the PCB, the junction temperature will be relatively low with high power dissipation applications. The maximum dissipation the package can handle is given by:
T *TA PD + J(max) RqJA
If junction temperature is not allowed above the maximum 125C, then the NCP511 can dissipate up to 400 mW @ 25C. The power dissipated by the NCP511 can be calculated from the following equation:
Ptot + [Vin * Ignd (Iout)] ) [Vin * Vout] * Iout
The enable pin will turn on or off the regulator. These limits of threshold are covered in the electrical specification section of this data sheet. If the enable is not used then the pin should be connected to Vin.
Hints
or
P ) Vout * Iout VinMAX + tot Ignd ) Iout
Please be sure the Vin and GND lines are sufficiently wide. When the impedance of these lines is high, there is a chance to pick up noise or cause the regulator to malfunction. Set external components, especially the output capacitor, as close as possible to the circuit, and make leads a short as possible.
If a 150 mA output current is needed then the ground current from the data sheet is 40 mA. For an NCP511SN30T1 (3.0 V), the maximum input voltage will then be 5.6 V.
100 ESR, OUTPUT CAPACITOR (W) UNSTABLE 10
1
Battery or Unregulated Voltage
C1
+
1 2
5 +
Vout C2
Cout = 1 mF to 10 mF TA = 25C to 125C Vin = up to 6.0 V STABLE
0.1
ON OFF
3
4
0.01
0
25
50
75
100
125
150
IO, OUTPUT CURRENT (mA)
Figure 16. Typical Application Circuit
Figure 17. Output Capacitor vs. Output Current
http://onsemi.com
8
NCP511
APPLICATION CIRCUITS
Input R
Q1
Input Q2
R1 R2 R3
Q1
Output 1 1.0 mF 2 3 4 5 1.0 mF
Output 1 5 1.0 mF 4
1.0 mF
2 3
Figure 18. Current Boost Regulator
The NCP511 series can be current boosted with a PNP transistor. Resistor R in conjunction with VBE of the PNP determines when the pass transistor begins conducting; this circuit is not short circuit proof. Input/Output differential voltage minimum is increased by VBE of the pass resistor. Enable Voltage (V)
Figure 19. Current Boost Regulator with Short Circuit Limit
Short circuit current limit is essentially set by the VBE of Q2 and R1. ISC = ((VBEQ2 - ib * R2) / R1) + IO(max) Regulator
Input 1 1.0 mF 2 Enable 3 4 5
Output 1.0 mF
4 3 2 1 0 3 2 1 0 0 20 No Delay mW R = 1.0 MW C = 0.1 mF 40 60 80 Time (ms) 100 120 140 160 R = 1.0 MW C = 1.0 mF TA = 25C Vin = 3.5 V Vout = 3.0 V
Output 1 1.0 mF 2 3 R C 4 5 1.0 mF
Figure 20. Delayed Turn-on
If a delayed turn-on is needed during power up of several voltages then the above schematic can be used. Resistor R, and capacitor C, will delay the turn-on of the bottom regulator. A few values were chosen and the resulting delay can be seen in Figure 21. Input R Q1 1.0 mF 5.6 V
Vout, Output Voltage (V)
Figure 21. Delayed Turn-on
The graph shows the delay between the enable signal and output turn-on for various resistor and capacitor values.
Output 1 2 3 4 5 1.0 mF
Figure 22. Input Voltages Greater than 6.0 V
A regulated output can be achieved with input voltages that exceed the 6.0 V maximum rating of the NCP511 series with the addition of a simple pre-regulator circuit. Care must be taken to prevent Q1 from overheating when the regulated output (Vout) is shorted to GND.
http://onsemi.com
9
NCP511
ORDERING INFORMATION
Device NCP511SN15T1 NCP511SN15T1G NCP511SN18T1 NCP511SN18T1G NCP511SN25T1 NCP511SN25T1G NCP511SN27T1 NCP511SN27T1G NCP511SN28T1 NCP511SN28T1G NCP511SN30T1 NCP511SN30T1G NCP511SN33T1 NCP511SN33T1G NCP511SN50T1 NCP511SN50T1G Nominal Output Voltage 1.5 1.5 1.8 1.8 2.5 2.5 2.7 2.7 2.8 2.8 3.0 3.0 3.3 3.3 5.0 5.0 Marking LBU LBU LBV LBV LBW LBW LBX LBX LBY LBY LBZ LBZ LCA LCA LCB LCB Package Shipping
TSOP-5
3000 Units/ 7 Tape & Reel
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. NOTE: Additional voltages in 100 mV steps are available upon request by contacting your ON Semiconductor representative.
http://onsemi.com
10
NCP511
PACKAGE DIMENSIONS
THIN SOT-23-5/TSOP-5/SC59-5 SN SUFFIX CASE 483-02 ISSUE E
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. A AND B DIMENSIONS DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. MILLIMETERS MIN MAX 2.90 3.10 1.30 1.70 0.90 1.10 0.25 0.50 0.85 1.05 0.013 0.100 0.10 0.26 0.20 0.60 1.25 1.55 0_ 10 _ 2.50 3.00 INCHES MIN MAX 0.1142 0.1220 0.0512 0.0669 0.0354 0.0433 0.0098 0.0197 0.0335 0.0413 0.0005 0.0040 0.0040 0.0102 0.0079 0.0236 0.0493 0.0610 0_ 10 _ 0.0985 0.1181
D
5 1 2 4 3
S
B
L G A J C 0.05 (0.002) H K M
DIM A B C D G H J K L M S
SOLDERING FOOTPRINT*
1.9 0.074
0.95 0.037
2.4 0.094 1.0 0.039 0.7 0.028
SCALE 10:1
mm inches
*For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT: N. American Technical Support: 800-282-9855 Toll Free Literature Distribution Center for ON Semiconductor USA/Canada P.O. Box 61312, Phoenix, Arizona 85082-1312 USA Phone: 480-829-7710 or 800-344-3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Fax: 480-829-7709 or 800-344-3867 Toll Free USA/Canada Phone: 81-3-5773-3850 Email: orderlit@onsemi.com ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder For additional information, please contact your local Sales Representative.
http://onsemi.com
11
NCP511/D

▲Up To Search▲

Price & Availability of NCP51106

	To Download NCP51106 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .